Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

光纤复合架空地线雷击断股的分析及试验

介绍了光纤复合架空地线(0PGW)雷击断股的特征，讨论了其原因和机理，并进行了0PGW的雷电冲击电波试验，分析了造成断股的影响因素，提出了防止雷击造成0PGW断股的措施。     

From Long Infrared to Very Long Infrared Wavelength Focal Plane Arrays Made with HgCdTe n + n ?/ p Ion Implantation Technology

This paper aims at studying the feasibility of very long infrared wavelength (VLWIR) (12–18 μm) focal plane arrays using n-on-p planar ion-implanted technology. To explore and analyze the feasibility of such VLWIR detectors, a set of four Cd _x Hg_1−x Te LPE layers with an 18 μ cutoff at 50 K has been processed at Defir (LETI/LIR–Sofradir joint laboratory), using both our “standard” n-on-p process and our improved low dark current process. Several 320 × 256 arrays, 30-μm pitch, have been hybridized on standard Sofradir readout circuits and tested. Small dimension test arrays characterization is also presented. Measured photonic currents with a 20°C black body suggest an internal quantum efficiency above 50%. Typical I(V) curves and thermal evolution of the saturation current are discussed, showing that standard photodiodes remain diffusion limited at low biases for temperatures down to 30 K. Moreover, the dark current gain brought by the improved process is clearly visible for temperatures higher than 40 K. Noise measurements are also discussed showing that a very large majority of detectors appeared background limited under usual illumination and biases. In our opinion, such results demonstrate the feasibility of high-performance complex focal plane arrays in the VLWIR range at medium term.     

煤巷锚杆支护技术的探讨

从巷道围岩强度,原岩自重应力,地质构适应力,煤柱留设宽度和巷道断面形状等方面对影响煤巷稳定性的因素进行了分析,提出了煤巷锚杆支护注意的6个问题。     

250W带功率因数校正整流电源模块的研制

功率因数校正技术越来越成为电源行业研究的热点。文中介绍了适用于雷达等设备的250W带功率因数校正整流电源模块的设计，分析了其中升压电感器设计、主开关管保护、控制电路消振、散热设计和表面贴装等关键技术，完成了实验研究，获得了满意的试验结果。     

Ability of a contactless inductive device for the characterization of the critical current versus temperature in superconducting rings at temperatures close to TC

Critical current measurements for three polycrystalline rings of YBCO, three Bi-2223, and one YBCO + Ag were developed from a temperature close to 80 K to the critical temperature using a previously reported contactless inductive device based on the transformer method. These data were used to analyze the ability of this device to characterize, in superconducting rings, the Ginzburg-Landau, Ambegaokar-Baratoff, and De Gennes regimes as well as the crossover temperature between them.     

Investigation on vapor-cooled current leads operating in a pulse mode

This paper describes transient numerical modeling for thermal characteristic of vapor-cooled current leads under pulse operation. The transient thermal analysis considers the temperature difference between a helium gas flow and a copper lead with temperature dependent properties of helium gas, copper and stainless steel. The numerical analysis was validated by an experiment with commercially available 100 A vapor-cooled current leads. A proper overloading factor calculation and the effect of intermediate cooling are presented for the current leads under pulse operation, which can significantly reduce heat input to a cryostat.     

Three dimensional boundary element analysis of internal cracks under sliding contact load with a spherical indenter

Using boundary element based three dimensional modelling for linear fracture mechanics, we present an analysis of cracking in a homogeneous medium subject to contact load. The proposed iterative solution procedure allows a simultaneous treatment of a reasonable number of partially closed cracks. It is shown that the most probable direction of propagation of a vertical internal crack is strongly dependent on its size compared to the contact radius and its location with respect to the axis of maximum normal load.     

Threshold and growth mechanism of fatigue cracks under mode II and III loadings

ABSTRACT The fatigue crack growth behaviour of 0.47% carbon steel was studied under mode II and III loadings. Mode II fatigue crack growth tests were carried out using specially designed double cantilever (DC) type specimens in order to measure the mode II threshold stress intensity factor range, ΔK_IIth. The relationship ΔK_IIth > ΔK_Ith caused crack branching from mode II to I after a crack reached the mode II threshold. Torsion fatigue tests on circumferentially cracked specimens were carried out to study the mechanisms of both mode III crack growth and of the formation of the factory‐roof crack surface morphology. A change in microstructure occurred at a crack tip during crack growth in both mode II and mode III shear cracks. It is presumed that the crack growth mechanisms in mode II and in mode III are essentially the same. Detailed fractographic investigation showed that factory‐roofs were formed by crack branching into mode I. Crack branching started from small semi‐elliptical cracks nucleated by shear at the tip of the original circumferential crack.     

高炉富氧鼓风的现状及机前供氧

阐述了高炉生产采用富氧大喷煤的必要性，国内高炉富氧鼓风的现状，以及机前富氧的优点和应采取的安全措施。